Residential · Toilets, sinks & showers
Toilet Repair in Markham
Most toilet faults live in the tank: a worn flapper leaking into the bowl, a fill valve stuck open, a lift chain snagged. Rocking bowls point at loose bolts or a failing wax ring underneath.
- Caulk and grout lines checked around the fixture
- Parts matched to the brand you already have
- Seized stops replaced while we are there
- Old fixtures and packaging taken away
- Licensed plumbers (details on request)
- Price agreed before work
- Call-only, no forms
- Tested before we leave
Signs you require toilet repair
The tank refills on its own each few minutes. You need to hold the handle down to get a full flush. The bowl drains slowly or requires two flushes. Water appears on the floor around the base. The toilet rocks slightly when you sit on it. A faint hiss comes from the tank long after flushing. Each of these points to a different part, and most are reasonably simple to repair.
Our routine on the day
We lift the tank lid and observe a flush cycle, because the movement of the flapper, fill valve and float tells us a great deal. Phantom refills usually point to a worn flapper or a warped flush valve seat. A constant hiss often means the fill valve is not shutting off completely. A weak flush can be a low water level, a partial clog in the trap, or mineral build-up in the rim jets.
For leaks at the base, the toilet is lifted off, the old wax ring removed, and the flange inspected. Cracked or loose flanges are repaired before a new seal goes in. Rocking toilets get shims and properly tightened bolts. Once the work is done, we flush several times and check for drips or movement.
Markham houses and what shapes this job
Hard water deposits clog the small rim holes and siphon jet that power the flush. In homes across Markham without water softeners, this is a common cause of weak flushing. Mineral scale can also stiffen flappers and make them seal poorly.
Toilets in older homes in areas like Markham Village, Thornhill and German Mills may be original fixtures, and parts for some vintage models can be harder to find. Newer homes typically have standard components that are readily available. Some homes have pressure-assisted or dual-flush models, which use different internal parts.
Subfloor damage is another concern. A slow leak at a toilet base can quietly rot the plywood beneath it over the years. If the floor feels soft, we will tell you and discuss repairs with you before setting the toilet back down.
Repair or replace?
Most toilets can be repaired cost-effectively. However, a cracked bowl or tank, or a very old high-volume model, may be better replaced. See toilet installation if that is the case.
Ring us without delay if
Call promptly if the toilet is overflowing, leaking at the base or will not stop running. A running toilet can waste a large volume of water in a single day; our water bill spike note explains how quickly that adds up.
The dye test: squeeze some food dye into the tank, then leave the handle alone for a quarter hour.
From the job notes of Plumbers in Markham
Job card · Toilets, sinks & showers
On the van for this job
- Wax rings, closet bolts, flappers and fill valves
- Cartridges for common shower and faucet brands
Signs you need this
- The toilet runs or refills on its own
- The shower goes scalding when someone flushes
What we check before we pack up
- Fill and drain the fixture and watch every joint
- Set temperature limits on shower valves
| Fixture | Parts that wear | What to know |
|---|---|---|
| Toilet | Flapper, fill valve, wax ring | Rocking means bolts or wax |
| Shower valve | Pressure-balance cartridge | Access panel saves tile |
How the job runs, start to finish
- 1
On the phone
Explain what the water is doing and where. We ask the age of the house and which valve or breaker to shut while we drive over.
- 2
Drop cloths down
Floors and cabinets get covered, the water or gas is isolated and the work area is lit.
- 3
Find the failed part
We open the trap, cleanout, access panel or wall where the fault is, and show you what we found.
- 4
Quote, then work
We explain what failed and what the fix costs; no cutting starts until you say yes.
- 5
Cut, fit, seal
Old parts come out, new pipe, valves or fixtures go in, and joints are soldered, pressed, crimped or glued.
- 6
Test and ticket
We run water, pressure-test or fire the heater, check for drips, clean up and leave a written ticket of what was done.